Honeycomb inclined tube technology installation essentials
Zhengda Water Supply is a manufacturer of honeycomb inclined tube packing. Zhengda specializes in the technical development and research of honeycomb inclined tube packing. We have professional filling installation technicians. The honeycomb inclined tube needs to be welded and formed. This must be done by professionals. Otherwise, if the installation is not good, the service life of the honeycomb inclined tube will be greatly reduced. Next, we will explain the honeycomb to you. Several essentials for the installation of inclined tube packing technology.
First, the bottom of the sedimentation tank is installed in the mud pipe
The installation sequence of the honeycomb inclined tube sedimentation tank generally starts from the bottom, and the installation of the bottommost mud drainage pipeline system is completed first, to ensure that the opening of the mud discharge pipeline meets the design requirements and is firmly fixed, and the inspection is completed, and then the next installation process is allowed.
Second, complete the installation of the honeycomb inclined tube filler bracket
According to the installation drawing of the filler bracket of the honeycomb inclined tube sedimentation tank, the filler bracket is first installed in place, all the welded joints are inspected firmly, the strength of the bracket is sufficient to bear the weight of the filler, and the anti-corrosion treatment is completed on the surface of the bracket;
Third, complete the honeycomb inclined tube hot connection
According to the ironing method of the honeycomb inclined tube packing, each inclined tube packing is packaged as a single ironing unit, and one unit is 1 m2 after the hot joining is completed, and the hot stacking is completed and stacked on the field (retaining a small amount of spare sheets for use).
Fourth, the assembly of the honeycomb inclined tube packing pool
The hot-filled packing unit is assembled from left to right in the upper part of the packing bracket. Always maintain the 60° angle, and each unit should be properly pressed when assembled in sequence. If the size is not right when assembled to the rightmost side, it needs to be assembled according to the size of the loose honeycomb honeycomb tube filler and assembled until it is fully in place.
Fifth, the upper part of the honeycomb inclined tube packing is fixed
Since the honeycomb inclined tube packing has a specific gravity of 0.92 which is slightly smaller than water, the inclined tube packing needs to be reinforced with 10 mm round steel from the left to the right direction after being assembled in the tank (the upper part of each unit packing requires two round steels to pass through). ), both ends of the round steel are reliably fixed on the wall of the sedimentation tank. After the round steel is installed, the loosening and floating phenomenon of the inclined tube filler during initial use can be well prevented. The round steel is protected by epoxy coal tar pitch.
Sixth, the operation and debugging of the honeycomb inclined tube sedimentation tank
(1) Check whether the water inflow is uniform, and may not cause impact on the sedimentation tank and affect the sedimentation effect;
(2) Adjusting the height and level of the water sump to the appropriate level to maintain uniform water output;
(3) After the above construction process, the filling of the honeycomb inclined tube sedimentation tank has been completed. After normal use, it is necessary to determine the sludge discharge period according to the concentration of suspended solids in the influent water, pay attention to timely sludge discharge, and ensure that the inclined pipe sedimentation tank always maintains a good operating state and satisfactory effluent quality.
The article comes from: http:// reprint please specify!
For more information on environmentally friendly materials and water treatment materials, please refer to: http://
Â
Double Grille Linear Light is the most outstanding luminaire design in the lighting industry. Grille is very effective in solving the glare problem (UGR<13, UGR<16 & UGR<19). It can easily be used on this Grille linear light. It has been resolved, and LiteHome often uses high color rendering index SMD on this product, (CRI>85 Ra, CRI>90Ra, CRI>95Ra,CRI>97Ra) to better restore the original color of the irradiated object.
This product is suitable for supermarket lighting with high light requirements.
Hanging Led Panel Lights,Track Lighting Ceiling,Retail Shop Lighting,Linear Office Lighting
SHENZHEN LITEHOME OPTOELECTRONIC TECHNOLOGY CO., LTD. , https://www.szlitehomelight.com