The toilet is one of the most important accessories in the bathroom, and its daily usage rate is also very high. If you use it for a long time, there will be some problems. For example, if the toilet inlet valve is not water , it will always be very annoying. Then, what are the reasons why the toilet inlet valve is not watery? What are the solutions for the toilet inlet valve that doesn't contain water? The following Xiaobian explains to you.
Why toilet water inlet valve does not stop water
1. The reason why the water inlet valve of the toilet is not water may be stuck. At this time, check whether the float ball or pontoon of the inlet valve is stuck. We can use a hand to move the float or float ball.
2. The reason why the toilet inlet valve is not watery is that there may be foreign matter inside the inlet valve, because this will cause the needle valve pressure chamber at the top of the inlet valve to be insufficient to form water stoppage. If this is the case, it is best to ask a professional to repair or purchase a new replacement because it is difficult to repair it yourself.
3. The reason why the water inlet valve of the toilet is not water may be that there is a problem inside the inlet valve, such as tiny debris or sand in the inlet valve body. If it is such a problem, it can only be bought again.
Toilet water inlet valve is not water solution
1. When the water inlet valve of the toilet is not water, firstly close the water inlet angle valve, and then take out the water stop flap of the water falling part to see if it is aging, deformed or there is no foreign matter adhesion. At this time to be fresh or change the water flap.
2. After closing the inlet angle valve, use a Phillips screwdriver to remove the broken shaped nut, replace the new shaped nut, and tighten the nut. At this time, it should be noted that when the overflow pipe is placed in the ceramic mounting hole, it must be formed with care, and it must be tightly tightened when it cannot be shaken.
3. Put the water in the toilet tank under the sink, then add the dark solution in the remaining water, and then see if there is any water leaking at the flush outlet. The leak can tell that the porcelain body is cracked. If there is no water leakage, the triangle valve should be opened slowly. Then place the water on the top of the water outlet and above the water stop flap. At this time, look for leaks. Wait until the water is released to the body lip. When the surface level, if the lips out of water to prove the body has cracked. At this time also close the inlet angle valve.
4. Because toilets are used every day, it takes a long time to clean the inlet valve regularly. We can remove the water inlet pipe of the tank from the left side of the bottom of the toilet bowl, and then remove the plastic nut at the bottom of the inlet valve. If there is a filter, we must also remove it. The filter is usually at the top. Then pick up the plastic cover, loosen the water-draining connecting rod, and then turn the rod upside down with a force in the opposite direction. After opening, remove the inside of the thimble pad and clean it and reinstall it.
The article concludes: After a long time in the toilet, the water stop valve may also be more than water. If you don't know the reason, you don't know how to repair it is a very troublesome thing. I believe we can help everyone by understanding the reason why the above-mentioned toilet inlet valve is not water and the toilet water inlet valve is not water-resolving solution.
Welding Mask is a type of headgear used when performing certain types of welding to protect the eyes, faceandneck from flash burn, ultraviolet light, sparks, infrared light, and heat.
welding
masks are most commonly used with arc welding processes such as
shielded metal arc welding, gas tungsten arc welding, and gas metal arc
welding. They are necessary to prevent arc eye, a painful condition
where the cornea is inflamed. welding masks can also prevent retina
burns, which can lead to a loss of vision. Both conditions are caused by
unprotected exposure to the highly concentrated ultraviolet and
infrared rays emitted by the welding arc. Ultraviolet emissions from the
welding arc can also damage uncovered skin, causing a sunburn-like
condition in a relatively short period of welding.
Welding Mask
Welding Mask,Welding Face Shield,Pp Welding Mask,Flip Type Welding Mask
Greateagle Safety Products Co., Ltd. , https://www.greateaglesafety.com