Yuba is our common household electrical appliance product. It has the effect of heating. It can make us feel warm and comfortable when bathing in the cold winter. The method of installing Yuba can also affect the use of results. For everyone to introduce the installation method of Yuba and install Yuba to pay attention to what.
Yuba installation method
1 First, determine the position of the ventilation holes on the wall, generally lower the fan outlet of the ventilator hood above the ceiling to prevent the accumulated dew inside the ventilation pipe from flowing back into the bathroom heater.
2. Installation method of Yuba In the second step, put a ventilation window on one end of the ventilation pipe, and the other end from the outside of the wall to the place where the ventilation window is fixed on the outlet of the exterior wall. Use cement to fill the ventilation pipe between the ventilation pipe and the gap of the ventilation hole. The length of 1.5M must be taken into account when installing the ventilation pipe. The distance between the installation center of the product and the ventilation holes must be kept at a distance of over 1.3M.
3. In order to increase the heating effect of Yuba, Yuba should be installed on the ceiling above the center of the bathtub or shower room. The required strength of the ceiling of the ceiling is not easily resonating with the material. After installation, the height of the bathroom fighter is off the ground. Should be between 2 meters and 2.4 meters, too high or too low will affect the use of results.
4. In the installation of Yuba is to first screw down all the bulbs, and then remove the spring from the mask on the ring and take the next cover, disassembly and assembly of infrared heating bulbs, the hand should be smooth, to avoid excessive force.
5. In the installation method of the bath heater , pay attention to connect one end of the cord to the panel of the switch, and connect the other end with the power cord to pull out from the opening of the ceiling, and connect the wiring diagram of the terminal column cover and the terminal sign to the cord. Cover the terminal cover, then fix the terminal cover with screws, and then insert the excess wire into the ceiling so that the cabinet can be smoothly inserted into the hole. Finally, put the ventilation pipe into one end of the room and pull it out again. Put it on the air outlet of the centrifugal fan cover.
6. Select the correct direction according to the position of the tuyere in your home and put the box of the bath in the hole. Then use 4 wooden screws with 4mm in diameter and 20mm in length to fix the box on the ceiling.
7. After aligning the positioning position of the mask of the Yuba with the positioning groove of the box body, insert the spring on the hanging ring corresponding to the mask, and carefully turn all the bulbs on so that the lamp holder can maintain good electrical contact. Then wipe the bulb and mask clean, and finally only need to fix the switch on the wall to prevent the normal use of the power cord to withstand tension.
Install Yuba to pay attention to what
Should pay attention to the installation of the reserved mouth, the size of the general Yuba open hole 300 * 300 mm, there are holes in the bathroom heater 300 * 400 mm hole, strip of aluminum strips, it is best to confirm when installing the pinch plate The size of the opening of the Yuba, when installing the gussets, will leave the distance of the mounting holes, and two more solid slats larger than the span of the main keel of the ceiling shall be prepared for the installation of the Yuba.
Xiao Bian summary: The above is a small series for everyone to introduce the installation methods of Yuba and install Yuba to pay attention to what, Yuba brought us a warm and comfortable life, but in the installation process or to pay attention to some details, I hope the above The introduction can help you. For more information, please continue to pay attention to this site.
The highest level of explosion-proof certification, suitable for a variety of inflammable and explosive high-risk sites
· Small volume, light weight, easy to install
· Low power consumption, small power consumption, design of convection heat dissipation inside the fuselage can work uninterruptedly for a long time
· Special seismic treatment, auxiliary infrared lighting, to adapt to different environment
· The product has the characteristics of small size and light weight. It is a special kind of transportation vehicle or narrow area for dangerous goods.
· The windows are sturdy toughened flat glass
· Made of stainless steel materials. Suitable for the use of strong corrosive environment
· Intelligent 3D ring design, the camera installation angle can be adjusted at 360 degrees
Vehicle Explosion Proof Infrared Camera
Car Infrared Camera,Mine Infrared Camera,Wireless Infrared Camera,Vehicle Explosion Proof Infrared Camera
Jinzhou Jinshi Mining Equipment Technology Co., Ltd. , https://www.jsminingeqpt.com