The wall in the rough room is generally a cement wall, so before the wall is decorated, it is necessary to carry out a detailed inspection of the wall. Thoroughly check whether the front of the cement that needs to be painted in the rough room is firm and flat. The plaster layer that spits on the wall is not strong enough or there are large gaps and vacancies. Xiaobian suggested that you can complain to the developer or the property, and ask for it to be redone. If the holes are repaired by yourself, it is feasible to use gypsum filling. Today, I will work with Xiaobian to learn about the steps to decorate the rough house .
Renovation of rough house steps - waste maintenance
Before the renovation of the wall, there should be other projects. After the wall is disposed, it will inevitably have dust, and when the putty is put, there will be putty, paint or other glue drops, so in the right Before the wall is renovated, be sure to carry out maintenance work on other waste products in the room. Generally, you can buy plastic paper of the appropriate size in a convenience store, and wrap the waste that needs to be repaired on the construction site, but be careful not to block the waste and prevent the damaged waste.
Steps to decorate the rough house - preparation before scraping the putty
Before scraping the putty, make sure that the wall is firm and flat. The uneven wall can be cleaned with steel brush or other tools. The recessed area can be filled with cement, so that the wall surface is free of floating soil and floating. On the wall roll, the concrete interface agent (the individual wall surface may need to be patched), and the roller should be averaged as much as possible. After it is boring, the putty on the wall can be applied.
Decorating the rough house steps - scraping putty
Before the putty on the wall in the rough room, the flatness of the wall should be measured first, and the measuring ruler of more than two meters can be used to measure. This way, the method of scraping the putty can be determined. Generally, the putty on the wall needs to be scraped twice by putty, which can equalize the wall surface and average the background color of the wall surface. If the flatness of the wall is poor, you can brush it up a few times. If the inclination of the wall or wall with very poor flatness is very large, you can consider first scraping the leveling gypsum for leveling, then after scraping the putty, the distance between the putty of each putty should be more than 2 hours (after drying) ).
Steps to decorate the rough house - what to prepare
(1) The tool is in place and ready
Before you decorate, you have to put a few things in your bag. Tape measure (buy 5m, don't 3m), calculator, large board clip (clip list, receipt); In addition, it is better to prepare old towels (soft cotton, paste bricks) on the construction site early, Plastic bag (wrapped on the pipe joint to prevent dirt infarction)
(2) Selecting a good day, starting the work
Before the workers enter the scene, it is good to measure the corners of the family and personally measure them. Take a pen ruler and record them clearly. Be sure not to be lazy. Regarding the wall decoration of the rough room, we must pay attention to the above steps, so that we can make a basis for a better decoration effect in the future. At the same time, you must also prepare the materials for the main decoration, so that you don't have to be too hasty in the decoration. When you are purchasing materials, you must go to a large manufacturer, so there will be a guarantee of quality.
The above is a detailed answer to the steps of decorating the rough house. I don't know if you are satisfied with the introduction of the decoration home network. If you want to know more about the related aspects of the decoration of the rough house, please continue to pay attention. Our decoration encyclopedia section!
More related wonderful reading:
How to decorate the rough room? Introduction to the renovation of the rough house
Steps to decorate the rough house yourself? What should I do?
Aluminum Strip is cut from Aluminum Coil.The alloy include 1050 1060 1070 1100 3003 3004 5052 8011.The tempers are O or H.O means soft.H means the hardness and the annealing of the aluminum strip.H14/H24 is half hardness,H18 is full hardness.At present,the first choice is temper O,that`s due to its easy drawing and easy bending character.
Alloy 1060 and 1100 have excellent moldability they are widly used in chemical equipment. A1100 also used in the food industry device and storage containers,sheet processing, deep drawing or spinning concave ware, welding part, heat exchanger, printing plate, nameplate, reflective instruments.Alloy 3004 aluminum strip mainly used for pipe extrusion tube for tensile use. This alloy is used to produce all aluminum cans.
Aluminium Strip Coil,Aluminum Strip,Aluminium Slitting Coil,Mill Finish Aluminum Strip
Henan Everwin Trade Co., Ltd. , https://www.ewaluminium.com